Select Page

Worm travel gearbox with motor
worm motor
A robust worm-get gearbox powered by an MM28 engine. Ideal applications where an easy to fit, high torque result is required. Ideal for student based assignments including robots and buggies.
The unit has been designed so that the output shaft could be ‘clicked’ in and out for modification. Electronic.g. cutting down to size. The motor is snap installed into its cradle to engage the gear and worm.
Details
1 – 6V DC
0.1A to 1A based on load
Driveshaft length: 12.5cm
Driveshaft diameter 3mm
Gearbox ratio: 42:1
Overall dimensions of box + electric motor: 35(W) x 40(H) x 60(L)mm
The primary feature of this high-efficiency gear box is a worm gear, which locks the output shaft whenever the motor is not turning. The high gear ratios of 216:1 or 336:1 get this to gearbox appropriate for little strolling robots, lifting mechanisms, and additional applications where great torque is desired.
The low-voltage motors in the worm gearbox operate on 1.5-4.5 volts and draw up to a few amps, making them perfect candidates for the DRV8833 motor driver carrier. Engine overheating can be due to excessive stalling, also at very low voltages. We recommend that you use stall-detection sensors, or just watch your robot, to make sure that it doesn’t stall for more than a few seconds at a time.
This gearbox includes a 4 mm diameter, round output shaft, which works with the wheels that are appropriate for Tamiya 4 mm, round shafts. Our 3 mm universal installation hub also fits on the smaller threaded end of the shaft, though it is not specifically designed to work with this type of shaft (the hub’s set screw could harm the thread on the shaft).
Ever-Power gear motors happen to be economical, right-angle, worm-geared motors that install easily in the tightest applications. Economical correct angle worm geared motors set new requirements for reliability, efficiency and economic climate with unparalleled features including hollow shafts in the smallest sizes. An inverter friendly style provides for easy integration today and a truly future proof answer. The Ever-Power gear engine offers total flexibility in mounting choices includes shaft, base, face, and flange solutions. The engine terminal box could be mounted in option positions rotated in 90º steps around the engine frame offering for unparalleled integration opportunities.
Ever-Power gear motors adhere to North American and International standards, including NEMA, IEC, CSA, and CE, the Ever-Power series allows for worldwide acceptance, a true total answer for our global clients.
Superior protection of IP65 acc. to IEC 529 assures you that the Ever-Power series is dust tight and hose evidence,and can be used outdoors or in wet and dusty environments without the use of additional enclosures. Full rated output is available at the result shaft of the unit.
Product Features
Power ranking up to 5,5 kW.
Torque 25 … 1.000 Nm
Output Speeds 0,2 … 300 min-1
versatile installation possibilities
Totally enclosed, sealed against dust and water spray
Lubrication change 1st after 15000 hrs
Low noise gearing
Mains connection 110 … 690V, 50/60Hz
Enclosure IP65 (Standard), IP66 (Optional)
Additional features:
Connecting with Connect connectors.
With integrated inverter up to 7,5kW.
Ever-Power-Mark
CSA, UL, ATEX, GOST, CCC, ISO9001, ISO14001, OHSAS18001
Motors according to EN 60034
Corrosion category based on DIN ISO 12944-5
C1, C2, C3, C4, C5-We, C5-M
DC WORM GEAR MOTORS
Ever-Power DC worm gear motors are the answer for applications requiring a corner turn, optional dual result, or perhaps an inability for the electric motor to be back again driven. The DC correct angle gear motors are made for continuous and intermittent duty procedure. Our right angle gear reducers are designed with several mounting plate options, making them perfect for a number of DC engine based applications. You can expect 12 ratios which range from 5:1 to 100:1.
10309
FEATURES
1/43 to 3/8 HP
12, 24, 90, 130, 180 VDC, 115 FWR
9 – 475 RPM
1.5 – 315.9 in-lb rated torque
Frame Size 60, 80, 108 mm
5:1 – 100:1 standard ratios
Regular brush life of 2000+ hours (varies by application)
EP Products Worm Gear Motors are made to generate high torque in a little package size. Worm Equipment Motors are excellent for applications that require a self- locking or breaking characteristic since the result shaft can’t rotate when there’s no power used. On top of that, Worm Gearheads can transfer motion in 90 degrees. With various reduction ratios, precision cut gears, voltages and sizes, EP Items includes a DC Worm Equipment Motor solution for the application.
Features and Benefits
HIGH Torque Capabilities
Self-Locking / Braking Features
Motion Transfer of 90 Degrees
Ability to Handle Large Gear Reduction Ratios
High Durability
Low Noise
Flexible Configuration
Applications
Security Door Locks / Industrial Conveying Devices / Security Gates / Dental care Chairs / Ambulance Cots & Stretchers Many of our DC Motors could be complimented with among our Worm Gearheads. EP Products will continue to work with you to design and manufacture a Worm Gear Electric motor that may optimize the overall performance of your unique application.
Built to your unique requirements
Engine Type: Brushed / Brushless / Coreless
Voltage
Output Speed
Power
Current
Torque
Reduction Ratio
Shaft Material & Size
Gear Material
Shaft Configuration: (D Slash / Round / Splined / Other)
General Size Parameters (L, W, H)
Encoder Type: Optical / Hall Effect
Extra Assembly Requirements (lead wires, connectors, etc.)
INTRODUCTION
The turbo metal gear worm engine uses a metal gear box for durability and a higher torque output. Due to the special mechanical structure of the worm travel the motor output shaft is definitely self locking and can not be rotated.
This part uses a two wire connection and supports direction control in addition to PWM speed control. Ranked voltage is 12v and can accomplish 40RPM, with a torque of 8kg/cm.
SPECIFICATION
Operating Voltage: 6 – 15 V
Rated Voltage: 12V
No-load Speed: 40 RPM
No-load Current: 35 mA
Rated Torque: 32 RPM
Rated Current: 180 mA
Ranked Torque: 2.2 kg.cm
Rated Power: 1.1 W
Stall Torque: 8 kg/cm
Stall Current: 1 A
Reduction Ratio: 1:150
Weight: 167 g
EP Geared Motors with Worm Gearing – Modual & Customizable drive technology
Worm gear products from EP DRIVESYSTEMS especially show their power in applications where high gear ratios are necessary. Our worm geared motors are consequently optimally suited for use in intralogistics, packaging technology and the meals & beverage industry.
Four great reasons for EP worm geared motors:
Rugged
Our worm geared motors have a high overload capacity
Maintenance Friendly
Washdown versions enable simple and efficient cleaning of the travel system.
Corrosion protection
The NSD tupH sealed surface area conversion is exceptionally chemical, corrosion and abrasion resistant.
Flexibility
Our modular style give users maximum freedom.
The modular system for maximum flexibility: Our EP worm gear units
There are numerous applications that require drive systems, and each one of these has its unique requirements. The EP series worm equipment motors could be quickly and effectively adapted to fulfill your needs.
Worm gear devices impress with their great power density and compact design. If required, we can also source them with the impressive nsd tupH surface area treatment.
As well as the basic EP housing, we offer an extensive line of bolt-on components to customize the merchandise including torque arms, shaft addresses and output flanges. These can be easily field set up, but we may also be glad to assemble the individual components for you.
Discover more about the modular SI worm geared motors!
Find out more
Smooth and Tidy: The EP worm gear unit SMI
SMI worm gear systems feature a clean, corrosion-resistant alluminum alloy housing. Optional nsd tupH surface area conversion makes the product preferably suited for severe and challenging industries like food processing and pharmaceuticals.
Versatile input designs such as for example NEMA, IEC or immediate motor mounts in additional foot or flange mounted housing designs.
Worm geared motors
Worm geared motors for small power range.
The WATT small worm gear unit adapt themselves concerning UNIBLOCK design optimally in the geared electric motor program. The units possess on all sides diverse fixing possibilities and enable an easy assembling for the client.
Various other drive configurationscan be designed by use of built-on add-ons (e.g. torque arm and result flanges). The housings are created in light weight construction out of aluminium die cast. Motor attachment is realised generally by means of IEC adapter B5 or B14A.
Technical Data
Number of sizes:5
Power Range:0.12 – 2.2kW
Output torque range:17 – 230Nm
Ratio:5 – 100
Output option:output shaft, result shaft on both sides, hollow shaft, hollow shaft with shrink disc
Assembly/mounting:uniblock, flange, torque arm
Buy Worm Get Gearbox with Motor – incorporating the following features: 1 to 6V voltage rating, 17100 rpm no load swiftness, 220g-cm stall torque, 3mm shaft size, 60mm long, 35mm huge, 40mm high, a good robust worm get gearbox powered by an MM28 electric motor (included), most suitable for applications where an easy to fit, high torque output is necessary, nylon housing and equipment, requires light oil or perhaps silicon grease lubrication, perfect for student based projects including robots and buggies.
Most suitable for applications where an easy to fit, high torque output is required
Ideal for student based projects including robots and buggies
Reversible Huge torque Turbo Worm Gear Motor JGY370 DC 12V 40RPM
Reversible Great torque Turbo Worm Gear Electric motor JGY370 DC 12V 40RPM
Features:
The motor is Gear DC engine with micro-turbine worm, you can transform the wiring-connection to change motor rotation.
Turbo worm geared engine with self-lock, that is, regarding motor without electrical, the end result axis is certainly fixed, self-lock.
The reducer output shaft arranged vertically with the motor shaft, whole motor output shaft relatively-short than general gear engine, widely used to be installed the dimensions requirements strictly occasion.
Specifications:
Model: JGY370
Voltage: DC12V
No load speed: 40r/min
Result torque: 5.6kg.cm
Rated current: 0.06A
Weight: 163g
Application: open the windows, door, Mini winch. Ect.
In sumo robot or combat robot competition where substantial holding torque’s engine is essential to avoid your robot being pushed by your opponent robot. The worm equipment is definitely a better option compared to the spur gear motor. Why is worm gear so unique? Take a look wiki out: Worm Drive.
“Unlike with ordinary gear trains, the path of transmission (insight shaft vs output shaft) is not reversible when working with large reduction ratios, because of the better friction involved between the worm and worm-wheel, when usually a single start (one spiral) worm is used. This is often a advantage when it’s desired to eliminate any possibility of the result driving the input.”
In other words, it is difficult to push your load (example, your robot) if the motor is not power or rotate.
Features and Spec:
Metal gear box
Output shaft is self-locking due to the worm gear’s characteristic
Rated voltage: 12V DC
Rated output speed: 150 RPM
Rated output torque: 117mN.m (1.2kgf.cm)
Stalled torque: 196mN.m (2kgf.cm)
No load current: 60mA
Stalled current: 1.8A
Output shaft diameter: 6mm with 4.5mm slot
Weight: 150g